[. . . ] Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. Warning Indicator When the "LAMP" indicator lights solid red, the projector will automatically shut itself down. When the "TEMP" indicator lights solid red for about 20 seconds, it indicates the projector has been overheated. Lamp will automatically turn off soon. " on the on-screen display. Under normal conditions, the projector can be switched on again after it has cooled down. If the problem persists, you should contact your local dealer or our service center. When the "TEMP" indicator flashs red for about 10 seconds, you will see a message "Fan fail. 14 This graph is for user's reference only. User Controls Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Control Panel Remote Control Using the Control Panel Power/Standby 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Source 4 Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources. Menu 4 Press "Menu" to launch the on screen display (OSD) menu. To exit OSD, press "Menu" again. Keystone /Keystone 4 Adjusts image distortion caused by tilting the projector (±16 degrees). Four Directional Select Keys 4 Use Enter your selection. to select items or make adjustments to 4 Confirm your selection of items. Auto Image 4 Automatically synchronizes the projector to the input source. English User Controls Using the Remote Control Power/Standby 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Re-Sync 4 Automatically synchronizes the projector to the input source. Volume + / - (Vol+/Vol-) Reset 4 Increases/decreases speaker volume. 4 Changes the adjustments and settings to the factory default value. Hide 4 Press "Hide" to hide image, press again to restore display of the image. Keystone / 4 Adjusts image distortion caused by tilting the projector (±16 degrees). Page Up (Computer mode only) 4 Use this button to page up. This function is only available Page Down (Computer mode only) when the projector is connected to a computer via an USB cable. 4 Use this button to page down. This function is only available Freeze when the projector is connected to a computer via an USB cable. 4 Press "Freeze" to pause the screen image. Four Directional Select Keys 4 Use Menu your selection. to select items or make adjustments to 4 Press "Menu" to launch the on screen display menu. To exit OSD, press "Menu" again. Enter 4 Confirm your selection of items. VGA 4 Press "VGA" to choose Analog RGB, component and HDTV source. S-Video 4 Press "S-Video" to choose S-Video source. English . . . 16 User Controls Composite 4 Press "composite" to choose Composite video source. DVI-D 4 Press "DVI-D" to choose DVI-D connector. 17 . . . English User Controls On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or Control Panel. 2. When OSD is displayed, use "Enter " key to enter sub menu. keys to select any item in the main menu. Use settings by keys to select the desired item and adjust the key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press "Menu" to confirm, and the screen will return to the main menu. 6. The OSD menu will close and the projector will automatically save the new settings. Main Menu Language Image-I Display Mode Brightness Contrast Keystone Color White Peaking Color Temp. [. . . ] 4 Check and reconfigure the display mode of your graphic card to make it compatible with the product. Refer to page 30. Problem: Image is out of focus 4 Adjusts the Focus Ring on the projector lens. 4 Make sure the projection screen is between the required distance 3. 9 to 32. 8 feet (1. 2 to 10. 0 meters) from the projector. 31 . . . English Appendices Problem: The image is stretched when displaying 16:9 DVD. The projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting. [. . . ]